Ruger 10/22 Photo Thread

Discussion in '.22 Rifle/Rimfire Discussion' started by notdku, Nov 27, 2007.

  1. notdku

    notdku Administrator Staff Member

    6,288
    8
    38
    Show off your Ruger 10/22 and please list what mods you have done to it.
     
  2. NY Marksman

    NY Marksman New Member

    73
    0
    0
    My Ruger Classic 10/22

    Here is my idea of the perfect classic 10/22

    •S&K Ultra Walnut Extra Fancy stock, 1 inch recoil pad and laser engraved

    •Trigger Work by Randy at CPC
    o 2.0 - 2.4 lb trigger pull
    o Trigger and hammer side shims
    o Trigger over travel screw
    o Forward anti-creep/slack screw
    o Auto-bolt release conversion
    o Single stage pull reworked to be as crisp as possible
    o Oversize receiver pins installed to tighten trigger group
    o Extended magazine release installed

    Bolt Work by Randy at CPC
    o Bolt is totally disassembled, cleaned, deburred
    o Bolt face is surface ground and squared to .0425" LR rim headspace depth; same as bolt action rifle for accuracy and reduced flyers
    o Bolt side is beautifully prism jeweled
    o A hole is E.D.M.'ed and a stainless dowel pin pressed in over the front of the firing pin to hold it from raising up, reducing flyers and to get more consistent firing pin strikes.
    o Bolt buffer installed.

    • 20 inch black fade to gun metal gray compensated whistle Pig barrel.

    • Superior Tactical Ruger logo charging handle, rod and spring.

    • Leupold 3-9 X 33 EFR VXII Gloss Black Scope

    • Leupold Low height rings.





    [​IMG]

    The rifle is also featured on Sturm Rugers photo galleries website in the "tricked out 10/22" section.

    I should also mention that the scope in the picture above is not a Leupold, it is a Center Point, and the barrel is a 18 inch Whistle. I am sorry for any confusion but the list and equipment was updated after I took this picture. Here is the rifle as it is today with the equipment as stated in the original post.

    [​IMG]
     
    Last edited: Dec 4, 2007

  3. Tanker60A3

    Tanker60A3 New Member

    48
    0
    0
    Cost?

    If I may ask, how much has this set up cost you so far?
     
  4. NY Marksman

    NY Marksman New Member

    73
    0
    0

    As of now I have a bit over $1500.00 invested. I know it seems like a lot but if you want a top of the line rimfire you have to be willing to spend whatever it costs to to bring your ideas to reality. I'm extremely satisfied with the way it came out.
     
  5. rickrem700

    rickrem700 New Member

    225
    0
    0
    Love the stock, when I first seen it I thought it was a curly maple, but I see now it is walnut, just beautiful, I have been trying to build up the courage to dump a butt load of money into a rim fire, for some reason I have always had a mental block when it comes to spending more than 2-3 hundred on a rim fire, I have been looking at pictures of 10/22 all dolled up on www.rimfirecentral.com most are bench type rifles, your gun has given me some insight to what I really want, a more usable rifle for the bench or the field, and it looks just strait sexy!!! I want to thank you for taking the time to post your rifle, you just made up my mind, I'm sure my wife will thank you to!!!
     
  6. Toxic

    Toxic New Member

    17
    0
    0
    Just a couple of plain jane 10/22's and a Krinker Plinker conversion.
    [​IMG]
     
  7. notdku

    notdku Administrator Staff Member

    6,288
    8
    38
    Nice look guns.

    Toxic can you go more into the gun on the left.
     
  8. Toxic

    Toxic New Member

    17
    0
    0
  9. notdku

    notdku Administrator Staff Member

    6,288
    8
    38
    I got a Ruger 10/22 Carbine for Christmas. Looking into getting a longer barrel. Will I need to replace the stock if I upgrade barrels?
     
  10. unclebill

    unclebill New Member

    2
    0
    0
    here is my sleeper 10-22
    shilen bbl. 1.005 in dia.
    many home internal mods.
    (the bbl. is the only after market item in or on this rifle.)
    pillar bedded.
    everything is stock except what i made myself.
    7 oz. trigger pull.
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  11. notdku

    notdku Administrator Staff Member

    6,288
    8
    38
    Amazing rifle Bill. How much do you estimate you have in it?
     
  12. Benelli29

    Benelli29 New Member

    20
    0
    0
    ny marksman where did you buy the stock i like it.
     
  13. mrdave

    mrdave New Member

    1
    0
    0
    Quality like your 10/22 takes time and money. Nicely done.
    Dave
     
  14. Ruger1

    Ruger1 New Member

    12
    0
    0
    Ny Marksman, I really like the new but classic look of your stock. Especially the Ruger logo. I'm going to start a new 10/22 project, who did your stock, I think I going to go along the classic line. Thanks and great gun.
     
  15. marysdad

    marysdad New Member

    107
    0
    0
    My first rifle. It's a 10/22 Deluxe Model, made in 1969 (s/n 15,xxx). Other than the receiver sight, just the way it left the factory. Wood sure is pretty. They don't look like that anymore.

    [​IMG]

    [​IMG]
     
  16. jeepejeep

    jeepejeep New Member

    695
    0
    0
    First of all NY marksman, that is the most beautiful 10/22 I've EVER seen! Wonderful job! Mary'sdad, I've only seen a pic of that style once before. What a great looking rifle! Leave it as is!

    Here are my two. The modified one has a Ram-Line folding stock and simmons 4X scope. The other was my Dads and became mine when he passed away. I will give it to my oldest son when I go.
     

    Attached Files:

  17. pioneer461

    pioneer461 New Member

    938
    0
    0
    Not fancy, but it's a tack driver!​


    [​IMG]

    Cabela's Co-Polymer free floating barrel.
    Leupold M-4 fixed power scope.
    Butler Creek Sporter stock.
    Internal milling, trigger job, etc. by Leupold engineer / gunsmith when I worked there. :)
     
  18. SimonTuffGuy

    SimonTuffGuy New Member

    130
    0
    0
    I agree! My new 10/22 doesn't look 1/2 that good!
     
  19. whiteknuckle

    whiteknuckle New Member

    1
    0
    0
    Custom Paint

    Here are some 10/22's that a friend has built and I painted for his collection. I am new to the 10/22 scene, my friend asked me to paint some and now I am hooked. I am in the process of building my own custom. Let me know what you think.

    [​IMG]
    Composite stock primed, painted black with true fire, clear coated, wet sanded and buffed. All automotive paint.
    [​IMG]
    Composite stock primed, painted metallic copper with black crytal effect, clear coated, wet sanded and buffed. All automotive paint.
    [​IMG]
    Composite stock primed, painted pearl white, clear coated, wet sanded and buffed. Reciever, trigger and rings are 24K goldleaf with clear. All automotive paint.
    [​IMG]
    Gray & black laminated stock, painted candy green with green true fire, clear coated, wet sanded and buffed. All automotive paint.