magazine cap swivel stud & stock swivel stud

Discussion in 'General Shotgun Discussion' started by old fart, Jan 31, 2014.

  1. old fart

    old fart New Member

    340
    1
    0
    i have a pardner pump protector, i love it so much i decided to get the regular pardner pump. the regular pardner doesn't have a stock stud or mag cap stud. the stock has the brass insert for the fine thread stud and the mag cap has the hole in it but no studs. i called h&r and they haven't got anything for it, they are getting it in but no time frame. any idea's what i can do? i think i can get the fine thread stud on ebay but the mag cap i haven't figured out. thanks for any help.
     
  2. beastmode986

    beastmode986 New Member

    967
    0
    0
    I have the same problem so ill be watching this thread, i'm gonna buy the magpul 870 stock but I still need the cap.
     

  3. old fart

    old fart New Member

    340
    1
    0
    has anyone tried these?, wonder how good the stud holds on the cap? (Uncle Mike's Quick Detachable Super Swivels for Most Pumps and Autos (Blued, 1-Inch Loop). these are sold by ecop on amazon
     
  4. Virginian

    Virginian Active Member

    1,081
    0
    36
    I have installed countless sets of Uncle Mike's studs on all kinds of guns, and all I can say is that they all worked exactly as advertised. I have the fore end cap studs on three different shotguns of my own that have been there for up to 30 years with zero problems.
     
  5. John_Deer

    John_Deer New Member

    6,624
    1
    0
    If you have a set of calipers you can easily see if the uncle mikes 870 stud will fit. If the stud won't fit try to borrow an 870 end cap. Most LGS will let you try before you buy. Might cost a few dollars more at the LGS but you will leave with a working part.
     
  6. AHGoodwin

    AHGoodwin New Member

    2
    0
    0
    I also just purchased a pardner pump. Got a Remington "Universal" Cap and stock stud kit. The cap fits great but the stud for the stock is too big. Been looking around for a week now to find a stud that will fit so I can get my sling on.
     
  7. old fart

    old fart New Member

    340
    1
    0
    i got the uncle mikes swivel set #1231-2, the machine screw in the set fits the stock, the other stud goes into the cap and a washer snaps in a groove. holds great and swivels good, got it on ebay for $16.00, but your local shop may have them. the set also comes with a long regular stock stud but i can't use it, i'll save it for another gun i have that it will fit.
     
  8. AHGoodwin

    AHGoodwin New Member

    2
    0
    0
    Thanks. Found it and it looks like it should work!
     
  9. Hookeye

    Hookeye Active Member

    1,226
    4
    36
    Some Remington synth stocks have the brass insert for machine screw swivel stud (IIRC 8-32). Those without the brass insert take the wood screw type.

    The magazine cap?

    I just drill mine out for the 8-32 machine screw type and cut whatever I need off and Loctite a nut after washer spacer. On my 1100's, since the mag cap is dished, I use a delrin spacer up front.

    Cheap (now maybe $5 tops) and works great, have done it this way for 30 yrs.


    Now, I did get a beater 1100 recently, where the mag cap was pretty torn up. I bought the new 870/1100/1187 super wonderful do all cap...........and whatever little clip they run, yeah that blew off in less than 10 shots. Mag cap stud stays on, due to shoulder.........but removing the cap lets it come apart.

    Fix cost 37 cents.....for a 3/8" snap ring.

    Everything new these days seems to be a pile of crap.
     
    Last edited: Mar 2, 2014
  10. Hookeye

    Hookeye Active Member

    1,226
    4
    36
    Cheap regular 8-32 machine thread type swivel stud w Delrin spacer (washer and nut on back, either Loctited or thread deformed to hold nut

    [​IMG]