Lathe

Discussion in 'Gunsmithing Forum' started by bwhsmith, Jul 22, 2010.

  1. bwhsmith

    bwhsmith New Member

    4
    0
    0
    I realize that this is a question that has been asked a million times, but can someone tell me what would be a good minimum size lathe for gunsmithing? Any info would be helpful :)
     
  2. greydog

    greydog Member

    158
    6
    18
    A 12x36 or 13x40 is probably the ideal. I've been using lathes of either size for gunsmithing work for over 30 years and they are just fine. An 18x60 I used for a while was OK in many respects but was too large and cumbersome for chambering. GD
     

  3. spittinfire

    spittinfire New Member Supporter

    9,663
    4
    0
    Hey greydog, what do you do while gunsmithing that you need a 13" swing?
     
  4. stalkingbear

    stalkingbear Well-Known Member

    4,095
    30
    48
    I agree with greydog on the size. The thing is you don't need that much swing but usually when you choose the length center to center then the lathe is made with that much swing. A 36" is big enough for anything I need to do.
     
  5. greydog

    greydog Member

    158
    6
    18
    A 13" swing also gives you a rigid headstock with a relatively large spindle bore. A large spindle bore allows you to work with a large diameter barrel through the tailstock. In addition, the larger the machine, the more rigid it is likely to be. This is a real benefit when contouring barrels, for instance. GD
     
  6. TheOldMan

    TheOldMan New Member

    1,014
    0
    0
    Not trying to hi-jack this thread but do you guys see that you need a lathe or a mill more?
     
  7. spittinfire

    spittinfire New Member Supporter

    9,663
    4
    0
    OK, I can understand wanting the larger lathe for it's beefiness and length. I couldn't picture anything gun related needing that much swing.

    I can't speak for them but in my experience having access to both a lathe and mill, the lathe gets used much more frequently then the mill. Don't get me wrong, when you need a mill, you need it but the lathe sees more action.
     
  8. bwhsmith

    bwhsmith New Member

    4
    0
    0
    Thank you for the replies everyone. I'm just getting started in the gunsmithing field and want to make good choices in buying my equipment. Does anyone have an opinion on combo machines? (lathe/mill)
     
  9. billdeserthills

    billdeserthills New Member

    774
    0
    0
    My experience with machines designed to do two or more things well, is that they don't do much of anything very well. Besides, the decent looking ones (Smithy) cost too much. Harbor Freight makes some real cheap & crappy ones...
     
  10. greydog

    greydog Member

    158
    6
    18
    You can mill things with a lathe but you can't turn things with a mill. This is not entirely true of course but it's true enough. With an inexpensive milling attachment for the lathe, one can do a respectable job of milling as long as cuts are light and the jobs small. For instance, sight dovetails and extractor cuts are easily done with a milling attachment on the lathe. GD
     
  11. danf_fl

    danf_fl Retired Supporter

    12,369
    57
    48
    I bought one of the "inexpensive" combo mill/lathe from harbor freight. Don't waste you money on it. Buy the best you can afford.
     
  12. progun3400

    progun3400 New Member

    18
    0
    0
    I have an old 820 Logan 10x24, my buddy has an Enco 12x36. It wasn't so much the swing that he utilizes it most for but the length. He said his next will be bare minimum 13x40, again not for the swing but sure would've made life easier spinning them .50 cal barrels. Another advantage the larger swing lathes can have is a larger through hole in the headstock?