VIEW MY

Sharps40

Gift Premium Subscription To Sharps40

Join Date:

03-13-2014

Last Activity:

02-05-2016 6:20 PM

Likes Given: 6

153 Likes on 118 Posts 

    ABOUT ME

  • Sanford, NC

LATEST ACTIVITY

  • Posted in thread: Busby The BearCat on 02-06-2016 at 01:23 AM
    Done. Got the last .002" shim between the cylinder and frame too. Not absolutely necessary but
    worth the fight to get it in there to put that last lil bit of snugging up into the action. I'm
    happy wit...

  • Posted in thread: Busby The BearCat on 02-05-2016 at 02:47 PM
    Goin with brown. Cylinder was in good shape, no real significant pitting so cleaned it with
    400g and left the original bluing down in the roll mark. Hopefully, it will show through
    somewhat. In any ev...

  • Posted in thread: Busby The BearCat on 02-03-2016 at 12:34 AM
    Busby is nearly done. Bottom end is back together and feels like its functioning right fine.
    The parts to rust blacken, Ejector Rod Housing, Gate and Cylinder pin. The question remains,
    blacken or bro...

  • Posted in thread: Chingachgook on 02-02-2016 at 11:12 PM
    Done and on. A grease shim between the mount and receiver bridge. Blue Loctite on all the
    screws and synched well and good for the long haul. A spot of rust on the sight slide....its
    old. The gun is o...

  • Posted in thread: Chingachgook on 02-02-2016 at 12:56 AM
    In for the first water boil to change red rust to black magnetite. First pass or two is usually
    a translucent light grey. A good place to stop if matching a new or recently cleaned original
    part to a ...

  • Posted in thread: Chingachgook on 02-01-2016 at 11:27 PM
    Well....since I gotta shoot this thing in and validate the front sight calculations, figgered
    no sense takin the receiver sight on and off. Just get it rust blackened and put it on once and
    for all.So...

  • Posted in thread: Chingachgook on 02-01-2016 at 01:18 PM
    Twas winter and the rifle laidRusting slow upon Smiths bench:All critics typed “You
    Hack” to slay,And the Wannabe’s cried STENCH! "Beware the Armchair King, my son!The
    words that bit...

  • Posted in thread: Chingachgook on 01-31-2016 at 06:08 PM
    Federal 170g PowerShok (my favoritest 3030 ammo) ranges somewhat as follows:Average Zero: +.3"
    at 50 yards --- 0" at 100 yards --- -8.4" at 200 yards --- -30" at 300 yards. So....A 200 yard
    maximum ra...

  • Posted in thread: Chingachgook on 01-31-2016 at 05:38 PM
    Made a buncha measurements, made a buncha calculations. Good news.....we should not need a
    ridiculously tall front sight of .65 to .8ish.The receiver sight center height was measured
    bottomed on the b...

  • Posted in thread: Chingachgook on 01-31-2016 at 03:39 PM
    Use the base and Prussian Blue to spot in the rough location of the mounting screws. Level
    lines and centers will be scribed later based off the single red dot. holes are drilled and
    tapped and the ...

FORUM SIGNATURE
A bit twitchy eh? I wasn't pokin ya in a eye or givin ya a atomicwedgie or yankin yer buttcheeks round yer ears nor hackin on yer hooptie. But we can ignore each other!
0 COMMENTS
POST A COMMENT