Firearm & Gun Forum - FireArmsTalk.com - Search Results


Firearm & Gun Forum - FireArmsTalk.com > Search Forums > Search Results

Showing results 1 to 9 of 9
Search took 0.03 seconds.
Search: Posts Made By: Stacheyboots
Firearms Forum: AR-15 Discussion 03-01-2013, 03:42 PM
Replies: 43
Views: 2,106
Posted By Stacheyboots
Can't we all just get along? I personally just...

Can't we all just get along? I personally just built my AR. I could have gone with a poly lower and it might have been fine. However after speaking with multiple gunsmiths, i was informed that the...
Firearms Forum: Gunsmithing Forum 02-22-2013, 06:58 PM
Replies: 2
Views: 266
Posted By Stacheyboots
I actually live rather close to PSA so I can just...

I actually live rather close to PSA so I can just go check em out and maybe get somethings while im there.
Firearms Forum: Gunsmithing Forum 02-22-2013, 06:40 PM
Replies: 2
Views: 266
Posted By Stacheyboots
AR-15 Parts?

I have been on the hunt for a lower parts kit at an affordable price. The issue is if i find them they are on backorder or out of stock and discontinued. Can anyone tell me where I may be able to...
Firearms Forum: XD Forum 02-22-2013, 06:36 PM
Replies: 33
Views: 2,233
Posted By Stacheyboots
I have jept my 92fs loaded for a lil over a year...

I have jept my 92fs loaded for a lil over a year now, and i havent had any issues. Not saying it doesnt happen, but i will be paying closer attention to it now.
Firearms Forum: Gunsmithing Forum 02-22-2013, 05:49 PM
Replies: 2
Views: 313
Posted By Stacheyboots
New screws are always the way to go.

New screws are always the way to go.
Firearms Forum: Gunsmithing Forum 02-22-2013, 05:45 PM
Replies: 19
Views: 1,321
Posted By Stacheyboots
Oh and just in case anyone is looking at the...

Oh and just in case anyone is looking at the remington R1's, those feed ramps arent even polished at the factory, and you will play hell trying to feed hollow points in them. Not a problem if you...
Firearms Forum: Gunsmithing Forum 02-22-2013, 05:39 PM
Replies: 19
Views: 1,321
Posted By Stacheyboots
No i wasnt having any feeding issues, i re-blued...

No i wasnt having any feeding issues, i re-blued the frame, so in turn i had to clean up the feed ramp, disconnector rail, and then did a trigger job on it. All of this meant lots of time getting the...
Firearms Forum: Gunsmithing Forum 02-22-2013, 05:03 PM
Replies: 19
Views: 1,321
Posted By Stacheyboots
I just polished my feed ramp on my 1911. I used a...

I just polished my feed ramp on my 1911. I used a foredom tool with a foot pedal for speed control. I used a piece of 1/8 in drill rod that i split down the middle with a really small jewelers saw. I...
Firearms Forum: Gunsmithing Forum 02-21-2013, 05:03 PM
Replies: 16
Views: 1,201
Posted By Stacheyboots
Hmmm... I have never seen a hammer pin go in from...

Hmmm... I have never seen a hammer pin go in from the starboard side before. Has anyone else had it apart? The recess cut for the pin head could just be done in the factory by simply using the same...
Showing results 1 to 9 of 9