Firearm & Gun Forum - FireArmsTalk.com > Search Forums > Search Results

Showing results 1 to 12 of 12
Search took 0.01 seconds. Search: Posts Made By: zombieresponder
Firearms Forum: Revolver Handguns 10-20-2012, 01:37 AM
Replies: 18
Views: 467
Posted By zombieresponder
I just saw this. I have a 1905 M&P in .38...

I just saw this.

I have a 1905 M&P in .38 Spl with a higher serial number and no "V" prefix. Mine was made right around the end of 1941, and a gun with a serial number close to mine went to...
Firearms Forum: Revolver Handguns 10-20-2012, 01:31 AM
Replies: 24
Views: 2,188
Posted By zombieresponder
I have one with the 1 5/8" barrel and both...

I have one with the 1 5/8" barrel and both cylinders. Mine's got the standard black rubber grip. I consider it little more than a novelty. Mine hasn't been out of the safe in a couple of years. On...
Firearms Forum: Revolver Handguns 10-20-2012, 01:22 AM
Replies: 18
Views: 467
Posted By zombieresponder
The cylinders are the same length. A .38 special...

The cylinders are the same length. A .38 special chambering reamer would be run into the .38 S&W chamber to make it longer. If you google "SAAMI chamber drawings", you should find a link to the...
Firearms Forum: Revolver Handguns 10-20-2012, 01:19 AM
Replies: 18
Views: 467
Posted By zombieresponder
What is stamped into the top or sides of the...

What is stamped into the top or sides of the barrel? What/where are any other markings? My best guess from what's been posted is that it's a .38 Military and Police "Victory" Model. If that's the...
Firearms Forum: Revolver Handguns 09-30-2012, 03:05 AM
Replies: 10
Views: 1,171
Posted By zombieresponder
Non +p is fine. S&W didn't start heat treating...

Non +p is fine. S&W didn't start heat treating cylinders until the late 30's or early 40's IIRC.
Firearms Forum: Revolver Handguns 09-29-2012, 03:46 PM
Replies: 2
Views: 155
Posted By zombieresponder
Pics aren't showing up? I'll take a semi wild...

Pics aren't showing up? I'll take a semi wild guess and say it's probably a .38 Military and Police, later known as the Model 10. Value will be higher as is than refinished, so stop whatever you're...
Firearms Forum: General Shotgun Discussion 09-29-2012, 02:05 AM
Replies: 9
Views: 1,176
Posted By zombieresponder
The part in red is incorrect. One does not have...

The part in red is incorrect. One does not have to be a licensed manfacturer to build a suppressor. An ATF Form 1 must be filed and approved, plus the $200 tax paid, and a few other minor things. The...
Firearms Forum: Revolver Handguns 09-29-2012, 01:52 AM
Replies: 4
Views: 251
Posted By zombieresponder
-5 = 5th engineering change = made between 1989...

-5 = 5th engineering change = made between 1989 and 1992(goes for this model only, varies among others). Nothing vintage about a gun made ten years after S&W stopping pinning barrels and recessing...
Firearms Forum: Revolver Handguns 09-29-2012, 01:42 AM
Replies: 15
Views: 1,041
Posted By zombieresponder
If I'm looking at the Standard Catalog of S&W...

If I'm looking at the Standard Catalog of S&W correctly, that is a .32 Safety Hammerless 2nd Model. Made between 1902 and 1909. It's chambered for the .32 S&W short. I wouldn't shoot it, but that's...
Firearms Forum: AK & SKS Discussion 09-25-2012, 12:44 AM
Replies: 41
Views: 1,751
Posted By zombieresponder
I've yet to see one shoot under about 3 MOA, in...

I've yet to see one shoot under about 3 MOA, in person. Having built a couple from parts and being a machinist by trade, I'm surprised they shoot that well given the wide tolerances and generally...
Firearms Forum: Revolver Handguns 09-24-2012, 02:53 AM
Replies: 26
Views: 1,037
Posted By zombieresponder
I've got one and have carried it many miles. I've...

I've got one and have carried it many miles. I've shot a fair amount of .357 mag through it too. I bought mine used for something like $250, been a while and I don't remember the exact number now. I...
Firearms Forum: Revolver Handguns 09-11-2012, 02:53 AM
Replies: 26
Views: 1,037
Posted By zombieresponder
Several gunsmiths offer machining services to...

Several gunsmiths offer machining services to recess the cylinder face for moon clips. Most of the time though, it's just to allow moon clips for whatever cartridge the gun is already chambered for. ...
Showing results 1 to 12 of 12

 

Newest Threads

Newest Classifieds

FOLLOW US ON