Firearm & Gun Forum - FireArmsTalk.com - Search Results


Firearm & Gun Forum - FireArmsTalk.com > Search Forums > Search Results

Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: alucas2006
Firearms Forum: Gunsmithing Forum 11-29-2012, 06:16 AM
Replies: 28
Views: 935
Posted By alucas2006
For those still interested in this... Took the...

For those still interested in this...
Took the marlin to the range today and put about 20 rounds through it, except I mounted a scope to it. My father in law had a never been used Bushnell 4x38...
Firearms Forum: Gunsmithing Forum 11-27-2012, 02:42 AM
Replies: 28
Views: 935
Posted By alucas2006
...forgot to call marlin today. The crown...

...forgot to call marlin today.

The crown doesn't look bad, but a couple inches down is abit of pitting, and spots here and there down to just above the thoat are pitted. To my surprise though,...
Firearms Forum: Gunsmithing Forum 11-24-2012, 10:06 PM
Replies: 28
Views: 935
Posted By alucas2006
I'll give them a call and see what it would be....

I'll give them a call and see what it would be. I'll let you guys know what I find out. It might be Monday or Tuesday though before I talk to a smith. Planning on going to the range again as well....
Firearms Forum: Gunsmithing Forum 11-24-2012, 08:02 PM
Replies: 28
Views: 935
Posted By alucas2006
I don't know if I would want to do a sleeve if it...

I don't know if I would want to do a sleeve if it were not threaded or bonded in a way that thermal expansion and contraction wouldn't effect it. (<<<< badly woorded sentence) I don't know much about...
Firearms Forum: Gunsmithing Forum 11-22-2012, 10:12 PM
Replies: 28
Views: 935
Posted By alucas2006
I'm located in tx, close to houston. I don't know...

I'm located in tx, close to houston. I don't know any around here personally, just spoken with a few from some stores around me. I the most of what the do is swap and fit parts. I havn't heard any of...
Firearms Forum: Gunsmithing Forum 11-22-2012, 10:10 PM
Replies: 28
Views: 935
Posted By alucas2006
Again, I appreciate all of your advice and I...

Again, I appreciate all of your advice and I think I'll leave it alone for now and see if I come accross a good deal on a barrel. It's still got me thinking though.

As far as dies, I'd bore out...
Firearms Forum: Gunsmithing Forum 11-22-2012, 09:24 PM
Replies: 28
Views: 935
Posted By alucas2006
To axxe55: My skills are mainly automotive...

To axxe55: My skills are mainly automotive bassed. I've rebuilt and swapped engines and have access to a lathe. I don't feel the cost of replacing or even having a barrel made would be worth it....
Firearms Forum: Gunsmithing Forum 11-22-2012, 09:13 PM
Replies: 28
Views: 935
Posted By alucas2006
I can understand that. How much do you think, or...

I can understand that. How much do you think, or any experienced smith, it might cost to have this done? I don't mind trying a failing because a few smiths have told me with the barrel the way it is,...
Firearms Forum: Gunsmithing Forum 11-22-2012, 07:40 PM
Replies: 28
Views: 935
Posted By alucas2006
Essentiall yes, similar to a 35rem, but with the...

Essentiall yes, similar to a 35rem, but with the smaller case, and lower pressure capacities of the 3030 case. I was thinking if I turned down some bushings to run a rod through it would keep the rod...
Firearms Forum: Gunsmithing Forum 11-22-2012, 06:12 AM
Replies: 28
Views: 935
Posted By alucas2006
Looking for opinions

Hello everyone, Thank you for taking the time to at least look at this. First off, I am a brand new member and haven't found what I am looking for reguarding what I'm looking to do.

I have a...
Showing results 1 to 10 of 10