Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   XD Forum (http://www.firearmstalk.com/forums/f59/)
-   -   Slide not locking back when empty (http://www.firearmstalk.com/forums/f59/slide-not-locking-back-when-empty-4411/)

charlescarr51 05-11-2008 06:41 AM

Slide not locking back when empty
 
I purchased my first handgun, my sub-compact XD40. I love the way it shoots and how it feels in my hand, but I am wondering why sometimes my slide will cock and load after the clip is empty. Its not happening everytime, I would say right around half the time it does it. Anyone else have this problem with their XD?

Jay 05-11-2008 10:29 AM

Make sure that neither one of your thumbs is preventing the slide lock from catching the slide.

Flint Rock 05-16-2008 11:57 AM

Your mag follower may be dragging a little bit on the inside of the magazine. That could slow the rise of the follower just enough to miss engaging the slide stop. Take your mag apart, clean it, and feel for burrs on the follower.

exdee 05-29-2008 01:54 AM

Quote:

Originally Posted by charlescarr51 (Post 23711)
I purchased my first handgun, my sub-compact XD40. I love the way it shoots and how it feels in my hand, but I am wondering why sometimes my slide will cock and load after the clip is empty. Its not happening everytime, I would say right around half the time it does it. Anyone else have this problem with their XD?

If it's a new gun, it should have 2 mags, check and see if it does it with both mags, if not but one and the same mag all the time, may be the mag. If it does with both mags, you may be hitting slide stop or limp wristing gun.

CA357 05-29-2008 02:15 AM

Not to be a smart a$$ or anything, but it's a magazine. A clip is something different. ;)

MarkoPo 06-01-2008 10:43 PM

Are you using your slide lock as a slide release? Some people like to push the slide lock down with their thumb to load the chamber. This is bad practice and can wear the edge off the slide lock causing it to malfunction. Always pull the slide back manually after inserting a new magazine to load the pistol and release the slide lock.

G21.45 06-02-2008 03:02 AM

Quote:

Originally Posted by CA357 (Post 25937)
Not to be a smart a$$ or anything, but it's a magazine. A clip is something different.

:) Likewise, I'm sure; and not to be a wiseguy either:

You are entirely incorrect!

(So, how about finally putting this popular internet myth to rest once and for all, hmmm .... .)






HERE! Look it up for yourself. ;)

charlescarr51 06-03-2008 03:51 PM

Sorry for the lateness in getting back here. To answer a few questions, yes sometimes I use the slide release to load the chamber, that will definitely stop from now on. Second, this happens with both mags but its not everytime. I just got done thoroughly cleaning the gun today and hopefully I can get out to the range on Saturday to see how that helped. Thanks again for all the replies.

G21.45 06-03-2008 08:35 PM

:) Wise decision, charlescarr51!

Your support hand should be over the top of the slide, toward the rear, with your palm facing down. Your trigger finger should be arrow straight. (Or, else, you're going to hear a sudden and really loud noise!) Pull the slide all the way back and let it go. Ideally, the muzzle should be pointed at the target when you do this. ;)

charlescarr51 06-04-2008 02:46 AM

I know how to properly close the slide, just didnt think there were any adverse problems by using the slide release only.


All times are GMT. The time now is 01:34 PM.

Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.