Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   1911 Forum (http://www.firearmstalk.com/forums/f57/)
-   -   Trigger Help (http://www.firearmstalk.com/forums/f57/trigger-help-93512/)

new_girsan_1911 07-07-2013 05:49 PM

Trigger Help
 
Ok got an issue with my Girsan MC1911HC, I replaced the stock trigger, hammer and grip safety about a month or so ago and just finally got it to the range. Well after every shot i have to physically grab the trigger and pull it back out. No real force was required to do this and i havent taken it apart yet but i am fixing to do so and just wandered what you all thought might be the issue......... I did have to fit the trigger a little bit but it felt really smooth when dry firing it and had a nice crisp break and barely any over travel. Thoughts?????

danf_fl 07-07-2013 08:59 PM

Was the trigger loose enough to fall out on its own?

If so, consider applying more tension to the center arm of the sear spring.

new_girsan_1911 07-07-2013 09:44 PM

Are you talking about the left arm of the main spring? Looking from the back of the gun?

new_girsan_1911 07-07-2013 09:46 PM

And the trigger does slide right out but wont fall out, but then my original trigger wouldnt just fall out either.

Fathead00 07-07-2013 10:25 PM

How was the trigger before you replaced it? I like going by the saying "If it ain't broke, don't fix it!!!!";)

new_girsan_1911 07-07-2013 10:55 PM

It had a lot of play up, down and side to side. It was ok as far as function. But i wanted a skeletonized trigger and a brushed stainless look instead of black.

rock185 07-08-2013 04:03 AM

new, I hope you'll have someone knowledgeable about 1911 work check out your modifications and fix what's wrong. I don't know quite how to put this, and mean no disrespect, but you should not be replacing critical fire control and safety parts without a thorough knowledge of what you'e doing. Every part you've mentioned normally needs fitting, and the required fitting is often not as obvious as having a trigger that won't physically fit without filing or stoning. There are many things that can go wrong with replacing the parts you indicated. I fully realize that the 1911 looks very simple, but with that there is considerable nuance in the platform, which is one reason gunsmiths get the big bucks... Best of luck with your project.

BillM 07-08-2013 04:22 AM

If the trigger is free in the slot, and it resets when you dry fire it OK---you
might have the trigger bow "pinched" in a bit, and it's dragging on the side
of the magazine.

danf_fl 07-08-2013 08:00 AM

There are three fingers on the sear spring.
The port (left side) keeps pressure on the sear.
The middle (center) keeps pressure on the disconnector and the trigger.
The starboard (right) keeps pressure on the grip safety.

BillM could be correct with the trigger bow. Do mags drop freely? Are there rub marks on any mags from the trigger bow?

new_girsan_1911 07-08-2013 06:48 PM

Dan thanks bro. You were correct, somehow i got confused on which leaf did what. But yeah the center leaf was a bit off looked like the whole spring was no set properly. But that center arm was the only one that didnt look right. I adjusted it and now works like a champ. Thanks for your input fellas, even the guy who said take it to someone knowledgable on 1911s. In my neck of the woods there isnt any good smiths but one and his shop in his house burnt down a few months ago. Besides i am confident with my knowledge and the knowledge and help i get from the wiser gentlemen here to do almost any repair to my gun. Thanks.


All times are GMT. The time now is 06:39 AM.

Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.