Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   1911 Forum (http://www.firearmstalk.com/forums/f57/)
-   -   Building a 1911 (http://www.firearmstalk.com/forums/f57/building-1911-a-4364/)

dragunovsks 05-06-2008 10:41 PM

Building a 1911
 
Thinkin about building a 1911. Can anyone tell how difficult it is? I'm a novice. Is it possible to put one together without any gunsmithing?

Dillinger 05-06-2008 10:44 PM

The short answer is probably not. But, it depends on how tight the tolerances you are shooting for is. You can buy a kit frame and parts from Brownell's and put the whole thing together in your basement, but I wouldn't recommend it unless you have the appropriate tools and experience to custom fit some of the parts...

JD

RONSERESURPLUS 05-06-2008 10:45 PM

Build of a 1911?
 
Hello all/Responce to Dragunov


It's not all that hard, but how up on the 1911 are you? Have you ever taken one dowen to nuts and bolts? Do you have good books to support that? I've built one, but I am a freak for 1911! I have good support and documents, you might wanna get those first!



PM me if you want additional information?

BigO01 05-06-2008 11:36 PM

Well I have looked into this a bit and the answer is yes and no .

Could you buy parts and just put them together ?

Perhaps but in the end it may cost you more than it would to buy a lower price end gun that can be very good , for instance a RIA or Charles Daly 1911 or even the basic Springfield can be had at reasonable prices .

You could say call up Caspian "http://www.caspianarms.com/index.php" and buy a frame , slide and barrel all together and ask them to make sure they mate up correctly but this alone would get you in the $500+ range , then one of the most importatant areas of the weapon are the fire control parts needs to be fitted for safety reasons "Hammer , Sear , Disconnector" if these are incorrectly fitted you could have a dangerous gun that could go full auto on you .

You can purchase kits from Cylinder n Slide http://www.cylinder-slide.com/ and the parts are all set but these will cost over a $100 Things like triggers and mainsprings , mainspring housings , grip safeties , thumb safeties , slide stops should all either drop in or be fit with a touch of sanding by hand with wet/dry .

www.MIdwayusa.com has almost everything you need listed for sale , go there and try adding up all the parts costs and see what you get .

All in all unless you truely want a custome gun I don't think it's worth it .

Heck if you just want a very nice accurate , reliable 1911 shoot me a PM and I have a Charles Daly full sized with a 5 inch barrel in blue I am selling for $400 . IT has a sweet trigger pull straight from the factory and yes she feeds hollow points .

I have a couple of Pics if you're interested .

dragunovsks 05-07-2008 09:09 PM

I actually have a RIA .45 1911A1 now, and yes, I've torn it down almost to the bare frame and cleaned it. Your right about this model being cheap, i got it for $300 at Keisler's Firearms in Jeffersonville Indiana. I thought about building a .45 stainless with a 6-inch slide, like the one in Terminator 2. I just wasn't for sure if I could do it with little experience and a basic set of tools.

dragunovsks 05-07-2008 09:13 PM

Forgot to say, thanks for the links, been looking for some stainless parts such as grip safety, trigger, thumb safety, mag release, etc to put on my RIA. It's the standard 5-inch 1911, all black, gonna put some stainless parts on it. It should look pretty good black and stainless.

BigO01 05-07-2008 11:33 PM

If you decide to change out the mainspring housing get a Swenson and save yourself some $$ , I put an Arched one in my Daly EMS "Midsized" and it slid right in no problem . The Swenson is anywhere fro $10-$30 less than the other brands and a mainspring housing isn't what I would call a major part anyway . Heck Colt and Kimber's new guns came with Plastic ones and I think still do .

dragunovsks 05-08-2008 12:55 AM

Thanx, the mainspring housing was one of the parts I am gonna change. My RIA has a straight one (black) but I think I'm going to put a stainless curved one on there. I held a friends 1911 with curved mainspring housing and it fits my hand a little better. Also thinkin about ambidextious thumb safety also stainless.

BigO01 05-08-2008 03:32 AM

O One thing when you swap the mainspring from one housing to another or just asseble one "if you get a totaly new assembly" I strongly suggest putting the housing in a vice to compress the spring into place and wear a pair of safety glasses.

If that little plug gets away from you and into an eye well kiss that eye Bye bye and get use to being nicknamed Cylops or Patch . That is one strong little spring and the cap is somewhat pointed .

yodar 05-25-2008 12:40 AM

Building a 1911
 
Quote:

Originally Posted by BigO01 (Post 23462)
O One thing when you swap the mainspring from one housing to another or just asseble one "if you get a totaly new assembly" I strongly suggest putting the housing in a vice to compress the spring into place and wear a pair of safety glasses.

If that little plug gets away from you and into an eye well kiss that eye Bye bye and get use to being nicknamed Cylops or Patch . That is one strong little spring and the cap is somewhat pointed .

I built mine from a Doublestar frame (centerfiresystems.com) $99
Centerfire also has ARMSCOR 1911 parts (Armscor makes the parts for many 1911 badges) Got a slide and match bbl with Wilson Combat sites at a funshow (er, gunshow) for $80.00 and all the innards from friends free!

Your talking bout mebbe a $200 gun that shoots betteren any of my nines

[IMG]http://pic20.picturetrail.com/VOL1229/6309647/12253703/245323460.jpg[/IMG

ONE thing I recommend strongly is read as much as you can, get the Army manual on 1911 maintenance and whatever else you can get, even surplusrifles.com has an excellent how-to manual.

And before you start, get a cafeteria tray and put a rubber mat in it for your small parts and disassembly/reassembly area



yodar


All times are GMT. The time now is 03:49 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.