Firearm & Gun Forum - FireArmsTalk.com > Gunsmithing & Do-It-Yourself Projects > DIY Projects > ,32 Colt rehab and an endorsement

Reply
 
LinkBack Thread Tools Display Modes
Old 04-19-2010, 10:57 PM   #1
Feedback Score: 0 reviews
 
superc's Avatar
 
Join Date: Feb 2010
Location: Winchester
Posts: 341
Liked 15 Times on 9 Posts
Likes Given: 8

Default ,32 Colt rehab and an endorsement

As some may know, one of my recent projects is the rehabilitation of a poor condition Colt 1903 Pocket Hammerless I picked up on gunbroker for a ridiculously low price. About what you would pay for two or three boxes of ammo at Walmart. Seems to be a transitional type III as it has the screw safety of the type I and II, the circled horse stamp on the slide, but also has no barrel bushing, and a patent date that only says Patented, vs. Browning or Colt Patent. I therefore make it to be around 1908 - 1909 manufacture.

When acquired the pistol had both broken leaf springs and compressed coil springs. The firing pin tunnel (and everything in it) was full of rust. Pins were corroded into place. The previous, perhaps the original(?) owner had clearly stored it loaded and cocked in a damp leather holster for decades as the entire slide was heavily pitted with visible rusting in spots. Oh yes, the gun was also dirty. After removing the grips I cleaned the gun in Hoppes 9 with an (outdoor) ultrasonic tank. Lots of sandy stuff was found on the tank bottom afterwards. I decided the bluing was beyond saving because of the extensive pitting and threw it all into a pail of Jasco to freeze any crevice rusting, then when that dried disassembled the pistol after a manual cleaning (cleaning the firing pin tunnel required some creativity) I replaced all of the springs and put it all back together. Mechanically, everything, including the safety mechanism was now fine and works perfectly.

A test firing showed the gun now worked just fine in both slow and quick firing sequences. Amazingly enough, although unmarked, the magazine appears to be an original Colt .32 magazine as the spring ends had the characteristic bend Colt put on their early springs. Further research showed that Colt did indeed make some magazines without the Colt .32 floorplate stamp in the earliest years of the 1903. Perhaps this was one? Whatever, replaced the rusty spring with a Wolff .32 spring and it works flawlessly.

In all honesty I considered the gun's exterior finish to be an almost total loss. As noted elsewhere I considered Parkerizing or Dura Coat to be the only options. While the frame had almost no pitting, the slide was very heavily pitted (which is why I suspect storage in a leather holster as the culprit) to the extent that some of the stamps were virtually gone. The pitting was such a shame though as the original stamps were so unique and historic to the gun. Then I remembered long, long, ago, on another website, seeing a post about someone buying a 'kept in the fishing tackle box' .45 and having the slide shaved and the stamps replaced.

Google research led me to several shops that specialize in such work. I picked one and after some correspondence with the proprietor sent off the slide to him. His prices were as posted on his website.

Before and after pictures follow. It really looks even better 'in the flesh' than the pictures show. I hope you enjoy this as much as I do. I feel like I somehow stepped back in time and am holding a spanking new 1903 slide ready for the bluing tanks at Colt. I am so stunned by the difference I am totally paused in my plans to Dura Coat the pistol and I am again reconsidering simply having it all blued to a near original finish.

This work is by Dale Woody of gun fancy com.

arrow.jpg   arrow2.jpg   horse.jpg   horse2.jpg  
__________________

Last edited by superc; 04-19-2010 at 11:10 PM. Reason: added a sentence
superc is offline  
 
Reply With Quote

Join FirearmsTalk.com Today - It's Free!

Are you a firearms enthusiast? Then we hope you will join the community. You will gain access to post, create threads, private message, upload images, join groups and more.

Firearms Talk is owned and operated by fellow firearms enthusiasts. We strive to offer a non-commercial community to learn and share information.

Join FirearmsTalk.com Today! - Click Here


Old 04-19-2010, 11:02 PM   #2
Feedback Score: 0 reviews
 
superc's Avatar
 
Join Date: Feb 2010
Location: Winchester
Posts: 341
Liked 15 Times on 9 Posts
Likes Given: 8

Default

one more view..

rightslide1.jpg   rightslide2.jpg  
__________________
superc is offline  
 
Reply With Quote
Old 04-20-2010, 12:20 AM   #3
Moderator
FTF_MODERATOR.png
Feedback Score: 0 reviews
 
c3shooter's Avatar
 
Join Date: Feb 2008
Location: Third bunker on the right,Central Virginia
Posts: 16,310
Liked 8374 Times on 3623 Posts
Likes Given: 1288

Default

That is OUTSTANDING! I reblued a 1903 a few years back- the right side was excellent- but the pistol had been kept on its left side in a drawer for years- sliding each time drawer opened/closed- and the left side bluing was only a memory. Those a great shooting little pistols- flat as a book, and points very naturally.

__________________

What we have heah is.... failure to communicate.

c3shooter is offline  
 
Reply With Quote
Old 04-20-2010, 01:42 AM   #4
FTF_SUPPORTER.png
Feedback Score: 0 reviews
 
CA357's Avatar
 
Join Date: Nov 2007
Location: Oregon
Posts: 19,871
Liked 1174 Times on 510 Posts
Likes Given: 2978

Default

Congratulations! You have done a great service for that old Colt and yourself.

As a gun lover, I salute you, as I'm sure old Samuel does too.

__________________
“If ye love wealth better than liberty, the tranquility of servitude better than the animating contest of freedom, go home from us in peace. We ask not your counsels or arms. Crouch down and lick the hands which feed you. May your chains set lightly upon you, and may posterity forget that ye were our countrymen.”Samuel Adams
CA357 is offline  
 
Reply With Quote
Old 04-20-2010, 02:00 PM   #5
Feedback Score: 0 reviews
 
superc's Avatar
 
Join Date: Feb 2010
Location: Winchester
Posts: 341
Liked 15 Times on 9 Posts
Likes Given: 8

Default

Well, as you will see the left side wasn't too bad, but it is a lot better now anyway.
Two more before and after views..

left2.jpg   left.jpg   sliderear.jpg   sliderear2.jpg  
__________________
superc is offline  
 
Reply With Quote
Old 04-20-2010, 02:23 PM   #6
FTF_SUPPORTER.png
Feedback Score: 0 reviews
 
CA357's Avatar
 
Join Date: Nov 2007
Location: Oregon
Posts: 19,871
Liked 1174 Times on 510 Posts
Likes Given: 2978

Default

Sweet! Please keep us up to date on the project.

__________________
“If ye love wealth better than liberty, the tranquility of servitude better than the animating contest of freedom, go home from us in peace. We ask not your counsels or arms. Crouch down and lick the hands which feed you. May your chains set lightly upon you, and may posterity forget that ye were our countrymen.”Samuel Adams
CA357 is offline  
 
Reply With Quote
Old 04-21-2010, 12:20 AM   #7
Feedback Score: 0 reviews
 
50of4064's Avatar
 
Join Date: May 2008
Location: Whittier,CA.
Posts: 107
Default

You have done yourself proud! What a sweet restoration.
What did it take for the metal work? ( besides blood, sweat and tears)
Well done!!! and thanks for the pix.

__________________
50of4064 is offline  
 
Reply With Quote
Old 04-21-2010, 06:52 PM   #8
Feedback Score: 0 reviews
 
GeauxTigersGuy's Avatar
 
Join Date: Apr 2010
Posts: 56
Default

Super cool. Can't wait for range report w/ porn.

__________________

"Owning a handgun doesn't make you armed any more than owning a guitar makes you a musician.” J. Cooper

GeauxTigersGuy is offline  
 
Reply With Quote
Old 08-19-2010, 07:24 PM   #9
Feedback Score: 0 reviews
 
superc's Avatar
 
Join Date: Feb 2010
Location: Winchester
Posts: 341
Liked 15 Times on 9 Posts
Likes Given: 8

Default

Just wanted to keep everyone abreast of where the project is going. I looked at a lot of finishes. Gave a lot of consideration to different types. Looked at samples of different ones too. Finally decided that the new finish would not be yellow or lime green (as incredibly tempting though that was to me). I haven't sent it off to Novak for the new sights yet, but as you can see we are progressing. The pins and safety are a glossy black and I will get more pics to you when the project moves forward a little more.

leftslide.jpg   patent.jpg   slideright.jpg   sliderightclose.jpg   rightsideall.jpg  

__________________
superc is offline  
 
Reply With Quote
Old 08-20-2010, 10:36 AM   #10
Retired
FTF_SUPPORTER.png
Feedback Score: 0 reviews
 
danf_fl's Avatar
 
Join Date: Apr 2010
Location: LA (Lower Alabama),FL
Posts: 10,032
Liked 2632 Times on 1535 Posts
Likes Given: 1168

Default

What finish did you finally use? It looks good.

__________________

Amendment II:
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."

Life Member NRA
Life Member NAHC
Former President of the ECPT (Eifel Combat Pistol Team)

danf_fl is offline  
 
Reply With Quote
Reply

Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Firearms Forum Replies Last Post
colt vs enhanced colt? Voltron 1911 Forum 6 01-28-2012 12:48 AM
Colt Address on Non-Colt Percussion Revolvers bprevolver Blackpowder & Musket 5 12-22-2009 11:55 AM
Base Prices for Colt .38 SN Detective/Colt .357 Python jknopp45 Revolver Handguns 2 02-14-2009 06:30 AM