Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   Ammunition & Reloading (http://www.firearmstalk.com/forums/f30/)
-   -   Trying to figure out what this. Ullet is called (http://www.firearmstalk.com/forums/f30/trying-figure-out-what-ullet-called-79302/)

keas3 12-24-2012 04:53 PM

Trying to figure out what this. Ullet is called
 
1 Attachment(s)
It's got a copper jacket with a lead hollow point! Does that mean I need to use XTP reload data? Or jacketed bullet reload data? I've been reloading just lead bullets and founds these for 38/357 with some other reloading stuff at an auction but don't know what they are really called so I don't know what to use to reload then?

c3shooter 12-24-2012 05:25 PM

It is a semi-jacketed hollow point. You can use jacketed load data- with the correct weight.

oldpapps 12-24-2012 05:26 PM

The bearing surface of the bullet is what counts, not what is or is not exposed at the ends.

robocop10mm 12-24-2012 10:12 PM

Typical SJHP for a .38/.357 revolver. Use JHP data. As with any data, you must reduce and work up a load. NEVER just load a max load and trust it to be safe. There are way too many variables to consider.

keas3 12-26-2012 05:09 AM

I've got the lee reloading manual and it has reload for a jacketed round! But I only have trail boss and bullseye powder! There a load for bullseye I can use for 158grain semi-jacketed hollow points for 357???

Axxe55 12-26-2012 05:29 AM

Quote:

Originally Posted by keas3 (Post 1066577)
I've got the lee reloading manual and it has reload for a jacketed round! But I only have trail boss and bullseye powder! There a load for bullseye I can use for 158grain semi-jacketed hollow points for 357???

use the powder manufacterers website and see if they have a load data listing for it. most of them do. just use the bullet weight that you have and start at the lowest charge weight and work up as needed.

locutus 12-26-2012 09:43 PM

Quote:

Originally Posted by keas3 (Post 1066577)
I've got the lee reloading manual and it has reload for a jacketed round! But I only have trail boss and bullseye powder! There a load for bullseye I can use for 158grain semi-jacketed hollow points for 357???

For .357 magnum loads, Bullseye is a poor choice.

2400, H110, 296, 4227 are all far better.

I use H110 exclusively in .357 and ,44 magnum loads. It;s never let me down.

robocop10mm 12-27-2012 03:00 PM

Bullseye is one of the fastest powders available. The large case capacity of the .357 makes Bullseye not only a poor choice, but also a potetntially DANGEROUS choice. I like Blue Dot or W-296 for .357 Mag loads.

TNFrank 12-27-2012 07:38 PM

You can use Unique and do a passable job loading the 357 Mag. I cut my teeth many, many years ago loading the 357Mag with Unique and 125gr JHP's. Also, you'll not need a mag primer for Unique, for the other, slower powders you'll need a mag primer to touch off that heavy load of powder.
Blue Dot would also be a good choice but having used quite a few powders over the years I've always came back to Unique. ;)

25-5 12-28-2012 12:14 AM

The hodgdon website has all kinds of reloading data. Real handy, and printable.
www.hodgdon.com/


All times are GMT. The time now is 08:27 AM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.