Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   Ammunition & Reloading (http://www.firearmstalk.com/forums/f30/)
-   -   Rusty 45ACP dies.. (http://www.firearmstalk.com/forums/f30/rusty-45acp-dies-57523/)

SmokyMtnHiker 02-12-2012 01:09 AM

Rusty 45ACP dies..
 
1 Attachment(s)
I bought this reloader from some one on craigslist. It's got some rusty parts. These are the 45ACP dies which the seller left in the die in the reloader. As you can see the previous owner didn't care well for the press. Looks like he just disassembled it a put it the box and forgot about it and it drew moisture.

What it the best way to clean this rust off these parts? The rust doesn't seem to be pitting. Would a brass brush, steel wool and some WD40 and/or Rust and Blue remover work?

This is just the start of the rusty parts pictures to come. Thank you in advance.

Txhillbilly 02-12-2012 01:25 AM

I have several die sets that look like that.If you don't have a climate controlled room-like inside your house-to reload in,the oil's,sweat,and humidity will allow the outside surfaces where you handle the dies to rust.
It doesn't do any harm,it just looks bad.A bead blaster works really good,but don't do the inside of the dies.Or,you could put them in your tumbler for a while.Just mask off the top and bottom of the dies to keep the media from scratching up the inside finish.

SmokyMtnHiker 02-12-2012 02:44 AM

Quote:

Originally Posted by Txhillbilly
A bead blaster works really good,but don't do the inside of the dies. Or, you could put them in your tumbler for a while.Just mask off the top and bottom of the dies to keep the media from scratching up the inside finish.

I dont have a tumbler yet. Slowly acquiring equipment..

If I were to soak them in blaster, scrub the outside rust off, then hit them with degreaser (non-chlorinated brake cleaner), let them dry then lightly coat with oil; would that work? I know they're used but I would like to get them looking as new as possible..

Sent from my SCH-I500 using FirearmsTalk

Axxe55 02-12-2012 03:33 AM

if there is no rust inside the dies, then most of that rust is more cosmetic than anything. i think your methods will work fine to rid them of the rust. steel wool and scotch brites with gun oil should work as well.

1hole 02-13-2012 03:52 PM

That's a harmless light surface rust on the dies, you probably don't have much if any inside. Chemical soaks and cleaners won't do much to rust but running over them with a rotating fine steel wire brush wheel will make them look new in a few minutes. Best would be with the wire wheel mounted on a bench grinder but one of the inexpensive and commonly available small circular brushes mounted on a 1/4" arbor and chucked in an eletric drill will also do it.

SmokyMtnHiker 02-14-2012 03:48 AM

I did a complete disassemble of the entire Lee Pro 1000 today. Soaked everything in wd40, scrubbed all the parts with a brass brush and steelwool.

When I bought the press I thought is was dirty but I didnt think it was this dirty. It turned the wd40 the color of light roasted coffee. I blasted all parts of the case carrier assembly with non-chlorinaded brake cleaner to clean off any wd40 that was still clinging on. Then I lightly greased (lithium) the bottom of the case plate. I also greased all the ram linkage. Runs like a champ now.

I have to give props to sfliberal's channel on youtube. He has a 9 part series on a complete Lee Pro 1000 strip & clean. I highly recommend his series to any first time, and even second time, cleaner of the LP1K.

Sent from my SCH-I500 using FirearmsTalk

General_Roc 02-14-2012 04:00 AM

1 Attachment(s)
.45 Auto

Attachment 39279


All times are GMT. The time now is 05:17 AM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.