Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   General Shotgun Discussion (http://www.firearmstalk.com/forums/f26/)
-   -   Winchester guys I need some info. (http://www.firearmstalk.com/forums/f26/winchester-guys-i-need-some-info-38390/)

DarinCraft 02-13-2011 04:44 AM

Winchester guys I need some info.
 
Several Winchester questions.

My wife shoots a model 120 20ga and I cannot find parts for it. I read on another forum that the 120 is the second generation 12 and the precursor to the 1200. One guy made a comment that 120 and 1200's parts are interchangable, but the comment was ignored with no confirmation or argument.

Anyone have any knowledge or advice?

Second question,
I have a 1400 as well that I absolutely love, and I was wondering is the 1400 considered a good gun? Maybe like the Remmy 1100 or not? Kind of running into the same problem with this gun. Very limited parts support.

Thanks guys

Virginian 02-13-2011 05:06 AM

Going strictly on recollection, the 120 was a lower cost 1200, plain uncheckered stock, etc,. but not at all sure about that one.
The 1200 and 1400 shotguns from Winchester were not well regarded, at all. The 1200 was known to break parts, among the most prevalent being the action bars where they were spot welded to the fore end tube.
The 1400 was considered very unreliable in functioning.

DarinCraft 02-13-2011 05:22 AM

Thanks Virginian, you have a pm.

Missileman 02-13-2011 06:39 PM

FYI, If you want the equivilant of the Rem 1100 in a Winchester you need to go back to the Super X Model-1, which hasn't been made for many years.

DarinCraft 02-13-2011 06:50 PM

Quote:

Originally Posted by Missileman (Post 444335)
FYI, If you want the equivilant of the Rem 1100 in a Winchester you need to go back to the Super X Model-1, which hasn't been made for many years.

Thanks, but I'm sure you guys are starting to notice a trend in me posting a lot of different questions about shotguns, from Remingtons to Winchester. I have too many field/trap guns and I am trying to decide which to keep for the long haul based on parts availability and durability.

I currently have the
1100 20ga magnum
1100 12ga
1400 12ga
120 20ga
AL391 Trap Gold.

My thoughts are to swap the internals on the two 1100's because the reciever on the 20 ga is in great shape and the 12ga has been powder coated because the previous owner didn't take care of it. The 20ga will be a loaner gun, the 12ga will be my clays gun(I am planning on attempting an adjustable comb), the Beretta will be my Trap gun and the 1400 as long as it will hold up will be my field gun.

robocop10mm 02-14-2011 01:08 PM

The 120 is the "Express" of the Winchesters. Bare bones, no frills, but mechanically the same. All parts interchange with the appropriate four digit model. I have a 120 that is just a good as my 1200 and 1300.

As far as I am concerned the 1200 is a very good shot gun. I have a 1200 defender I bought new in 1982. It has at least 5k through it and has never given me the first bit of trouble.

My agency was probably the single largest user of Defenders. We had over 350 in the inventory. We started aquiring them in 1985. I have seen 3 or 4 action bars broken over 20+ years. In comparison, I have seen at least that many shell stops come unstaked on 870's in the last 5 years.

DarinCraft 02-14-2011 04:41 PM

Thanks Robo. That was what I was hoping, but I couldn't find any info about the 120. I cannot get my wife to give the 120 up which is fine, but I couldn't find any parts for the "120" specifically. My wife was pretty disappointed when I told her "as far as I could find there are no parts for the 120." I'm glad I was wrong.

Any other opinions on the 1400?

Thanks again Robo
Darin

c3shooter 02-14-2011 06:59 PM

For future reference- when trying to figure if parts swap, quick check- go to Numrich on line parts catalog (gunpartscorp.com) Look up make, model and a specific part (firing pin, extractor, widget retraining brace spring screw stop) and note the PARTS NUMBER- not the 1 or 2 digit number, but the LONG number that Numrich uses. Then go to the other model and look at same part. Same number= same part.

DarinCraft 02-14-2011 07:01 PM

Quote:

Originally Posted by c3shooter (Post 445257)
For future reference- when trying to figure if parts swap, quick check- go to Numrich on line parts catalog (gunpartscorp.com) Look up make, model and a specific part (firing pin, extractor, widget retraining brace spring screw stop) and note the PARTS NUMBER- not the 1 or 2 digit number, but the LONG number that Numrich uses. Then go to the other model and look at same part. Same number= same part.

Thats a great reference. Thanks

robocop10mm 02-15-2011 12:32 PM

Just be aware of the exact replacement. There are some subtle differences between the 1200 and the 1300. I am not sure if the 120 was ever made as a bare bones 1300. Mine is pure 1200. Bolt carriers and ejectors are different. The bolt carrier MAY interchange. The ejector is different. Barrels, stocks and trigger groups are the same.


All times are GMT. The time now is 07:35 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.