Firearm & Gun Forum - FireArmsTalk.com > Long Guns > General Shotgun Discussion > 12GA FH- Hairy Shotgun/Rifle-

Reply
 
LinkBack Thread Tools Display Modes
Old 10-30-2012, 01:57 AM   #211
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

I found pictures of a factory 12ga over under that
has bottom barrel rifled, top one smooth with screw
in chokes. Will have pics few days. Don't know
how heavy barrel is yet.

Also will have pictures and test of brass 585HE sent
here. They are 585HE case samples from the first big
run of my 585HE cases, Bertram is doing.Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 11-04-2012, 12:11 AM   #212
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

Here is breach picture of that 12ga O/U made by Armi-Lumar
It has the bottom barrel rifled right from factory, top barrel smooth,
with interchangeble chokes. A real neat gun.



Good news, I got few samples of first production run of my 585HE
cases from Bertram, to test for strength and measure for uniformity.
They all measure perfect and especially the belt length headspace.
He made part of the run, a 1000, without headstamp..And over 3000
with headstamp. Cases only 3 bucks each if you get in on the first
shipment right away..Ship by mail to US cost too much, $1.50 each,
so we will have a bulk freight shipment to US as big as possible.
Folks in other countries order direct from Bertram.

This case can be used in different style guns.,
Bolt, Falling blocks, Break actions, Etc. I have reamers, and dies.
Manson Reamer can make more reamers,CH4D has dies also.
Earlier in thread I've shown various 585HE guns we have set up. Here
is a break action, with 585 barrel monoblocked in, one my favorites,
we just got done.




I tested 585HE moderate loads(650gr @ 2400) in NEF, CBC, Pedretti,
etc, break actions and didn't need sizing on the bottom 2/3. Real
tough built cases. Cases, are real uniform. For high test loads we
fired couple with 650gr at 3000 in Enfield bolt action, and it extracted
ok, and resized ok back to specs. About a 62k psi load. Pockets tight.

First picture, shown is some he made without headstamp that I stamped,
and some with stamp and ones I made on the right..
Also they can be used for wildcats, shorter cases, etc, and folks can stamp
what they want. 2nd picture you see them in a regular # 31 shellholder,
they don't need a special holder.

In 3rd picture of sectioned cases, you can see how strong the cases are
in base and corners, strong like the ones I made, on the left in picture,
which were real strong cases, that worked great with max loads..
The new 585 from Bertram on the right in picture.Nice strong base/corners.
He supplies same base cases for 408 Cheytac, used with hot sniper loads
that run real high average pressures..He will be manufacturing
these Cheytac runs regular, so we can get ours made anytime
we get money built up for an order..Ed







__________________
hubel458 is offline  
tCan Likes This 
Reply With Quote
Old 11-19-2012, 03:03 AM   #213
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

Here is overall view of the Armi-Lumar O/U 12ga that has
one barrel rifled. Second is another view of the breach.
Nice looking gun.





Here is picture of the 58cal Minie bullets in 20ga BPI Commander
shotcup wads, and some 50cal bullets in 20ga BPI Sport shotcups.
Sport wads were too small inside and to tapered inside for 58 cal.
Other two are 458 bullets in a non-discarding base that had SPW,
Buckhamer type slugs in them, that someone took apart, that I got.
And one 100yd group shot by Ajay on ShotgunWorld with Sav 220
20ga, with 20ga Commander wad and 58cal cast Minie bullets
measured about 2 inches. Four shots in two inches.Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 12-06-2012, 05:02 AM   #214
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

First is picture of the 8ga Falling Block with texturized paint finish
on the stock. It enhances the grip quite a bit on hard recoil guns.



Second is the Greener that I have my 585 HE in.Also have
12ga barrel for it..



Third is Magtech singleshot action that I'm experimenting
with putting on a thumbhole stock.



Fourth are the long bmg bulleted blank cases that I found, to use to
make my 700HE Long case, 4.27" long. I have few extra sets of
five in links like shown, extra to sell 5 at a time in links,
if some need them for their collections, etc... Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 12-06-2012, 05:06 AM   #215
Feedback Score: 0 reviews
 
tCan's Avatar
 
Join Date: Aug 2011
Location: Wake, NC
Posts: 1,128
Liked 112 Times on 78 Posts
Likes Given: 85

Default

I'm curious. Obviously you're making custom kit (i'm not sure if this includes receivers). Does the BATFE consider your shotguns to be shotguns or destructive devices? I guess that would only be a possibility with rifled barrels, but I'll still ask the question.

__________________
[Remington 870 12GA][Stoeger Model 3500 12GA][Savage 116 .30-06][Savage Model 10 Bull Barrel .223][Marlin 336SS .30-30][Marlin 39A .22][Marlin Model 60 22LR][Beretta PX4 Storm 9mm][Ruger MkIII 22LR]

They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety.

Terry V Ohio Commentary
tCan is offline  
 
Reply With Quote
Old 12-06-2012, 06:30 AM   #216
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

I don't make kits, I just tell others how to do it, and anybody
can legaly make up hopped up shotguns and it is not a DD.
Like take 3" 12ga and ream to 3.5 inch or 3.25" or whatever.
Gca law says shotgun calibers exempt.They only list certain styles
of gun like streetsweeper. If guns chamber takes shorter shotgun
style straight sided cases, of the same gauge it is legal shotgun
caliber, it don't matter how long case is or how much power it has.
Or whether barrel is smooth or rifled or polygonal or parodox
as these were all around before law was. Or what the case
is made from.Barrels are just marked with gauge and length.
My other rifle wildcats over 50cal have sporting use exemption
from being a DD approved by ATF.Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 01-02-2013, 07:50 AM   #217
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

In our research to find economical and easy to use setups to load
various slug/sabot combos in 12, 20 and other gauges, you've
seen what we are doing with 58cal slugs in 12ga accutip type sabot we
are getting built, and 58cal slugs in 20ga BPI Commander shotwad.
You've seen pics of group shot by Ajay 58cal in 20ga Commander wad.
And Greg Sappington made 16ga HP slug that fit 12ga BPI CSD wad.
CSD wads are little thicker. In that vein we found another 20 ga combo
that uses the BPI 20ga CSD wads and larger diameter of the 54cal
muzzleloading slugs. Wad is thick and short so we can get the
volumne of our slow powder we want in the loads for higher speeds.
And base of CSD 20ga wad is thicker and stronger than most wads.
. It doesn't have built on cushion, doesn't need cushion, which is not
needed for slow powder loads. Has a good built on powder seal.
It is long so it can be cut to fit any 54cal slug length.
Best 54cal slugs to use are .543" and up.
There is .548" Sharps style 2nd in picture from Dixie Gunworks.There is
54cal Great Plains in picture on left, Far right in picture is 550 Magnum
jacketed bullets in 20ga CSD. Great for hogs, bear. There are a variety
of 54cal slugs you can cast or buy. Not big number like 58cal, but enough
to find good simple combo. Shot 3" group with 54cal Great Plains in
CSD at 30 yds, smooth bore. 380gr going over 2000 fps.
Second picture shows they even work and fit good in 20ga RMC brass.
Fits in a brass case real tight with .548" Sharps style slug in picture..





Third picture shows how we mono-block 585HE barrels into strong
singleshot break actions. Done it in NEFs, CBCs, Pedretti, Beretta,
and the Magtech 199 shown above.



Fourth picture is the O/U Tristar with 585HE on top and 3.5" 12ga bottom.
We sleeved the top barrel with .585" ID sleeve. We will use it with
the 58cal .585" Minie hollowbase slugs. Bottom just for shot loads
with a interchangeable chokes. Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 01-14-2013, 05:35 AM   #218
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

Little work on non-discarding 12ga sabots,You can get SPW
wads without slugs in them and we set up one for a light load.
We put a 20ga Lyman in some and they stay together ok. Just
shorten the bottom skirt of Lyman and bevel the bottom corner.
Total weight sabot and all is 360gr,,Shown In the picture..
We also shrunk the skirt of the 12ga Lyman cast slug and put it
in 12ga SPW wads and total about 550gr. If you have Lyman
12ga mold, can use it as pattern to make a slug to go into a
SPW wad. Leave the top part same as original Lyman and make
bottom so it fits in the SPW with real tight fit.



I like to use P14/M17 Enfields for our testing. Great for my 585HE
case and in picture it shows how we change the sear spring to one
on the back of the sear. So we can open up the bottom to feed
the long cases from singlestack magazine box by removing the
unneeded front of the sear and metal above it in the bottom, giving
room to the back, for cases that are 3.9" plus overall loaded length.



Couple guys who are setting up 585HEs in singleshots are going
to shoot 58cal Minies and other bullets and use black powder
and/or substitutes. So I tested some with Pyrodex pellets,
Used 54cal, 60gr equivalent and they stack in the case ok,
and just beveled corner of bottom one so it set tight to the base.
As the case has good inside radius. Used 3 pellets with 24ga
card over pellets, 3/8" felt wad and another card with 440gr Minie.
There is a certain nostalgia about all that sulfur smell.If you can
stand the cleaning. Slug going 2100.. 4 pellets about 2400.

Here is picture of another long bullet in sabot/wad , in 12ga that
was sent to me. Ajay on Shotgun World put these together.



Did some testing, 12ga plastic & brass with new super slow RE-33 powder.
It fires off ok in 12ga with 700gr and heavier slugs, with shotgun primers
like RE-17 which is much slower than shotgun powders. .
It is made the same way as RE-17 as far as how the rate of burn
deterrent is put into the powder. Which is why it ignites in large diameter
cases like 12ga and BMG with shotgun primers. Really be great for super
heavy 1100 to 1500 grain slugs to get good speed and keep case damaging
peak pressures down. Example in 3.5" Fiocchi 12ga plastic case, 690gr slug in
BPI Helix Driver Wad with 180 gr RE-33 the basecup only expanded .002".
And they are thinner basecup than some..Ed

__________________
hubel458 is offline  
tCan Likes This 
Reply With Quote
Old 01-31-2013, 06:36 AM   #219
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

Last picture above shows what can be with sabots. It was thought to
be 20ga size when we got picture, but it is a smaller
45cal caliber sabot with 30cal streamlined bullets in them.
This was set up by the poster 'edge' on Castbullets forum.

More info on the SPW sabots with 520 gr Lyman reworked and locked into
them. With 3.5" brass RMC in the NEF long barrel gun, going about 2500
they smash though 6" timber with Lyman tearing wood up. Also got the same
combo 2200 in 3.5" plastic. Lyman in sabot on the left in picture on
right is factory SPW.



Another setup using the largest diameter 58 Minie I have is this .590" in this
12ga real thick muzzleloading wadcup for steel shot. I chamferred the bottom of
Minie slug and wedged it in the cup. The cup comes real long and we cut it off.
That leaves perfect edge to roll crimp against. Dab of epoxy holds the Minie slug
in, so it works like a non-discarding sabot. This wad has is own seal and fairly
short compared to others, so it leaves room for more of our slower powders.
Shorter slug and wad setups make loading easier.





Here is picture of the Magtech we redid in the 585HE by mono-blocking in 585
barrel. This is second one we've done. Tried out a ladder peep sight on the
back. Makes a neat gun.That underlever is a great touch.Ed




As part of the 585 test guns have smooth barrels, they are like a hopped up
24ga. We got couple bags of 24ga cards and felt wads. Easy way to use
reduced loads as the wads are perfect in 585 case. For comparison top load
say with RE17 and 650gr bullet is 170gr, but you can put in 100gr and card
and couple wads and have real easy load. And you don't have to worry about
airspace. Great for reduced loads with Minie slugs. In the same vein you
can put in a card over the powder and about 3/4 oz of shot and have a real
speedy 24ga shot load equivalent. Put card over the shot and glue it in.Ed

__________________
hubel458 is offline  
 
Reply With Quote
Old 02-26-2013, 04:01 PM   #220
Feedback Score: 0 reviews
 
Join Date: Jul 2008
Posts: 242
Liked 10 Times on 9 Posts

Default

First picture is of a nice finished 87 Winchester Will Sanders got set up
and he is using short brass cases.Beautiful scroll work on the stock.



Next is takeoff of a slug idea from Longbow on Cast Boolits, 12ga lead
roundball with section copper tube, wads compressed inside, BPGS seal on
bottom, screwed together. I have many boxes of wads. Now he did his with
screw into ball, put tube on with screw centered inside tube and filled tube
with hot glue. It stays together. Both are nose heavy for smooth bore work.



Next is side sectioned view, one of our 585HE cases, showing how 3/4
ounce of shot fits in.. 585 is same bore as 24ga. Cards shown are 24ga.
Just glue top card in. Some of our 585s are smoothbore and the HB Minie
slugs work at short range and the shot will do at short range also going
about 2000 fps. Could use 24ga shotcup.



Next, Mossy 390 bolt action, with heavy 585 barrel. Makes a nice big bore gun,
and handles nice with texturized stock finish. About same strength as
the heavy break actions I have 585HE in.Ed

__________________
hubel458 is offline  
 
Reply With Quote
Reply

Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Firearms Forum Replies Last Post
1800's rifle & shotgun PineKnot Blackpowder & Musket 4 02-21-2012 11:34 PM