Patch Thickness?


Firearm & Gun Forum - FireArmsTalk.com > General Firearms Forums > Blackpowder & Musket > Patch Thickness?

Reply
 
LinkBack Thread Tools Display Modes
Old 05-25-2007, 07:41 PM   #1
Feedback Score: 0 reviews
 
Join Date: May 2007
Posts: 3
Default Patch Thickness?

I have a .50 cal Cabela's Hawken with 1 in 48 twist. I am looking for some feedback on patch thickness. From what I have been told, you have to experiment with what works best in your gun. Is there a patch thickness that more often than not will work best in most guns? Will prelubed versus split lubed make a big difference? Is there a general rule about how tight the patch and ball should fit?



__________________
topgun is offline  
 
Reply With Quote

Join FirearmsTalk.com Today - It's Free!

Are you a firearms enthusiast? Then we hope you will join the community. You will gain access to post, create threads, private message, upload images, join groups and more.

Firearms Talk is owned and operated by fellow firearms enthusiasts. We strive to offer a non-commercial community to learn and share information.

Join FirearmsTalk.com Today! - Click Here


Old 07-08-2007, 07:34 AM   #2
Feedback Score: 0 reviews
 
Join Date: Jul 2007
Posts: 50
Default

Quote:
Originally Posted by topgun View Post
I have a .50 cal Cabela's Hawken with 1 in 48 twist. I am looking for some feedback on patch thickness. From what I have been told, you have to experiment with what works best in your gun. Is there a patch thickness that more often than not will work best in most guns? Will prelubed versus split lubed make a big difference? Is there a general rule about how tight the patch and ball should fit?
I am going to ask, you are planning on shooting round ball, and not conicals? I do not know what your experience is with BP, so it is best to ask. If you are going to be shooting conicals, you do not need or use a patch.

For pre-cut patches use a pre-lubed or unlubed .010 to .015 inch patch. If you use an unlubed patch, forget about "spit patches" you probably do not have that much saliva! Just use any of the commercially available lubes, they are all pretty good. If you cut your own use pillow ticking, which averages between .015 and .018 inches, and in any case a .450 round ball.

It is difficult to describe how tight the patched ball should be going down the barrel. Obviously, a clean barrel is going to feel different from one that has been fired, and what powder you are using can make a big difference too. Genuine Black Powder loads a lot different than Pyrodex after the first shot, due to the amount of fouling the powders leave behind. The fit of the patched ball should be snug; a couple pounds pressure to push the ball down. If you have to hammer the ball then it is time to clean the barrel.

The 1:48 twist is a bit fast for a round ball, so try some conicals too.
__________________

Gun Control is a MUST! If you cannot control your gun get one you CAN!

deerhuntguy is offline  
 
Reply With Quote
Old 08-03-2007, 06:28 PM   #3
Feedback Score: 0 reviews
 
Join Date: Aug 2007
Posts: 66
Liked 24 Times on 17 Posts

Default

Quote:
Originally Posted by topgun View Post
I have a .50 cal Cabela's Hawken with 1 in 48 twist. I am looking for some feedback on patch thickness. From what I have been told, you have to experiment with what works best in your gun. Is there a patch thickness that more often than not will work best in most guns? Will prelubed versus split lubed make a big difference? Is there a general rule about how tight the patch and ball should fit?
The general rule is what ever shoots best for you. Cabela's hawkens are made by investarms, & in those bbl's that ive shot, ive found a tighter patch/ball combo shoots best. In the one .50 bbl i have, an .018 patch around a .495 ball works best.
With the 1:48 you'll probably find midrange loads of FFG give the best accuracy. work around the 60 to 70 Gr range and see what shoots best.
I've found caps have alot of effect on accuracy too.
__________________
spottedpony is offline  
 
Reply With Quote
Reply

Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Firearms Forum Replies Last Post
infotech's morale patch design thread canebrake The Club House 24 04-03-2009 03:55 AM
Thickness of Grip? allabouttactics Revolver Handguns 0 05-18-2007 04:34 PM