Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   .22 Rifle/Rimfire Discussion (http://www.firearmstalk.com/forums/f21/)
-   -   rossi .22 pump model 62a (http://www.firearmstalk.com/forums/f21/rossi-22-pump-model-62a-82564/)

acfd813 01-27-2013 03:36 AM

rossi .22 pump model 62a
 
Hey y'all I'm new here but I have a Rossi .22 pump model 62a and I was shooting it a while back and it just stopped ejecting the spent casings. When you open the chamber there is a flat bar but one of the corners looks like its broke off. Does anybody know if this is why it won't work and if so where can I get parts and how do you replace it. Thanks in advance

Drriley 01-27-2013 04:28 PM

From your post, I am assuming the casing is extracted, but not ejected from the gun.

If you can post a picture of the broken part, it would help.

The actual eject is done by the carrier lifting and the rear corner of the carrier is cut out
to clear the bolt. It does not eject until the action is fully to the rear, pushing the spent cartridge
up and out of the extractor.

It may just be a cleaning issue. Dirt not allowing the action to move fully to the rear.

Numirich (www.gunparts.com) has the parts list
( http://www.gunpartscorp.com/Manufacturers/Rossi-33467/Rifles-40394/62SA-39620.htm)
but is showing sold out of the part.

Hope this helps.

acfd813 01-28-2013 01:00 AM

1 Attachment(s)
I will try to post a pic but it doesn't extract either the casing stays in the same spot I had to pry it out with my pocket knife

Attachment 82110

hiwall 01-28-2013 02:55 AM

Then it is an extractor problem.
I can not see the extractor in the pic.

acfd813 01-28-2013 03:03 AM

Do u want me to take the screw out and take it apart and take another pic?

TNFrank 01-28-2013 03:09 AM

You will have an extractor that pulls the case from the chamber by the rim and you will have an ejector which hits the case when it's about all the way to the rear of the action and flips it clear of the action.

shooter88 01-28-2013 03:51 AM

1 Attachment(s)
Wow i didnt know rossi makes a winchester clone i have a 62a but its winchester...

Attachment 82131

gunsmoke11 01-28-2013 04:14 AM

Shooter88, Rossi's made them for quite a while and they appear to be very popular. I also have a Winchester, but it's a model 62 pre war.
http://i1265.photobucket.com/albums/...ps809a049b.jpg
http://i1265.photobucket.com/albums/...ps864e1bd0.jpg
http://i1265.photobucket.com/albums/...ps652dd1aa.jpg

shooter88 01-28-2013 04:17 AM

[QUOTE="gunsmoke11;1113271"]Shooter88, Rossi's made them for quite a while and they appear to be very popular. I also have a Winchester, but it's a model 62 pre war.

Well i learn something new everyday thats a nice rifle

Drriley 01-28-2013 12:29 PM

From the picture, the carrier looks ok. The cutouts are are supposed to be there.

If the problem is the shell not being pulled out of the barrel, it could just be dirt build
up in the barrel (chamber). try a good cleaning with a brush.

I can not see the extractor in your picture as the carrier has already lifted past and
would have ejected the casing if it was there. This rifle does not have a bar that
ejects the shell
, but uses the upward motion of the carrier to push the casing out of the ejector.

Breaking down the rifle will not show the ejector, as it is on the bolt which will stay closed.

if you pull the action partially back you can see the small hook on the side of the bolt (right hand side).
if it is damaged or missing, that is your problem.


All times are GMT. The time now is 11:46 AM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.