Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   Revolver Handguns (http://www.firearmstalk.com/forums/f16/)
-   -   Colt Trooper MKV .357 Magnum Sights (http://www.firearmstalk.com/forums/f16/colt-trooper-mkv-357-magnum-sights-8115/)

sspbrad 11-01-2008 12:55 AM

Colt Trooper MKV .357 Magnum Sights
 
I've got a Colt Trooper MKV .357 Magnum and I was going to take it deer hunting this year. Its my dads gun and he used to use it for target shooting and when I switched to a heavier grain bullet and went to sight it in, I couldn't raise the rear sight enough to put the bullet on target before the screw on the sight comes out of its threads. Any one have any solutions or a reason this would be like this? thanks

freefall 11-01-2008 02:06 AM

I had that problem after I got my Super Blackhawk cut to 5". Couldn't raise the rear sight high enough. Had a smith tig weld about 1/4" blob on top of the front sight, cranked the rear halfway down, and filed down the front until it shot where I wanted. You could possibly file down the rear sight blade(much cheaper) but mine would have gotten awfully shallow...

Mark F 11-01-2008 11:02 AM

Quote:

Originally Posted by sspbrad (Post 48102)
I've got a Colt Trooper MKV .357 Magnum and I was going to take it deer hunting this year. Its my dads gun and he used to use it for target shooting and when I switched to a heavier grain bullet and went to sight it in, I couldn't raise the rear sight enough to put the bullet on target before the screw on the sight comes out of its threads. Any one have any solutions or a reason this would be like this? thanks

Rather than "risking" messing up your Fantastic Colt Trooper, Use a different load. The round you are using is way too low velocity, and you are trying to compensate with rear sight. Go back to 158 grain... or use Buffalo Bore Ammo. OR you could SIMPLY raise your POA when you aim... I do this a lot and I hit my target EVERY TIME!

Please don't cut, trim, or modify that revolver in any way! It will TOTALLY destroy its value.

Franciscomv 11-02-2008 12:53 AM

I agree with Mark F, try to find a solution that doesn't involve modifying the gun. Perhaps trying different ammo or just elevating the point of aim a bit.

Bob Wright 11-03-2008 01:33 PM

From what you state, the "heavier" bullet impacts too low?

Normally, if sighted in with a light bullet, the heavier will hit high.

But, if as you say, your rear sight is raised to maximum, file down your front sight. The old adage holds true, move your rear sight in the direction you want your bullet to strike, move the front sight in the opposite direction. To raise point of impact, lower your front sight. This is easily done with a good file.

First sight in with the ammunition you plan to use. Set your rear sight at about mid-point of elevation. Fire five shot groups and file the front sight, say about ten strokes, between groups. You should see your groups "walk" up into the black. When sighted in, touch up the blade with cold blue.

No matter how desirable a collector's item it is, its worthless if you can't hit with it.

Bob Wright

dmickey 11-12-2008 02:19 AM

Quote:

Originally Posted by sspbrad (Post 48102)
I've got a Colt Trooper MKV .357 Magnum and I was going to take it deer hunting this year. Its my dads gun and he used to use it for target shooting and when I switched to a heavier grain bullet and went to sight it in, I couldn't raise the rear sight enough to put the bullet on target before the screw on the sight comes out of its threads. Any one have any solutions or a reason this would be like this? thanks

Everyone forgets. It is not your gun to modify!! :eek:


All times are GMT. The time now is 09:33 AM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.