Firearm & Gun Forum - FireArmsTalk.com

Firearm & Gun Forum - FireArmsTalk.com (http://www.firearmstalk.com/forums/)
-   The Club House (http://www.firearmstalk.com/forums/f12/)
-   -   My Posts Are Going Halter - Scalder (http://www.firearmstalk.com/forums/f12/my-posts-going-halter-scalder-4130/)

Dan64456 04-16-2008 01:46 PM

Cleaning the Glock 30SF Question
 
Ok, so I've done a fair amount of research and watching of videos of glock cleaning... I hear a lot of bad press about allowing lube or solvent leak into the firing pin channel... Now I am nervous about cleaning that area of my gun. I am completely new to this and this is my first firearm, so I just want to make sure I am doing it all correctly. I'm assuming the "breech face" is simply the wall of the slide where the firing pin pokes thru? If that is correct, would it be safe to use a toothbrush with a bit of solvent on that area to clean it? (Then of course drying it thoroughly?) If someone can go into more detail for what is safe and what I should not do I'd greatly appreciate it. The manual that came with it doesn't go into very much detail at all and I'd like some info on how to safely clean that rear area of the slide.
-Also is it safe to use a little bit of solvent on the plastic frame part of the gun? Thanks very much.

Dan64456 04-17-2008 03:35 PM

Ok, so now I read that you should keep the slide pointed down toward the table when cleaning the breach face area... (To prevent any solvent from leaking into the firing pin hole...) My next question is am I supposed to pull the firing pin back into the slide before cleaning the breach face area?

HankStone 04-17-2008 07:01 PM

My Posts Are Going Halter - Scalder
 
WHY??I got me half? Nuts!!

robocop10mm 04-17-2008 07:30 PM

Any solvent advertised for gun cleaning should be safe with the plastic frame and other parts. You could get inito trouble if you use some industrial or automotive chemicals instead. Starting fluid (Ether) or carburetor cleaner can turn the frame off white.

The gun should be detail stripped every year or 1000 rds (whichever comes first) by a competant armorer/gun smith. You can get a build up of gunk in the striker channel that can cause some problems including failure to fire.

Dan64456 04-20-2008 03:18 PM

Quote:

Originally Posted by robocop10mm (Post 21961)
Any solvent advertised for gun cleaning should be safe with the plastic frame and other parts. You could get inito trouble if you use some industrial or automotive chemicals instead. Starting fluid (Ether) or carburetor cleaner can turn the frame off white.

The gun should be detail stripped every year or 1000 rds (whichever comes first) by a competant armorer/gun smith. You can get a build up of gunk in the striker channel that can cause some problems including failure to fire.

Ok, but when I do a general cleaning (after a day at the range), when I clean the breach face area, am I supposed to "retract" the firing pin first? Or do I leave it in its "striked" position to keep the hole a bit more closed off? I know I'm not supposed to let any solvent or lube leak into the firing pin channel, and I'm also nervous about getting any on the firing pin itself? Please let me know... thx

Dan64456 04-22-2008 02:29 PM

And I think it's nonsense that the subject line was tarnished on my OP... I posted this under the GLOCK forum because it is asking about a GLOCK handgun. I don't understand why it was moved and edited by a moderator?

bkt 04-22-2008 09:25 PM

Quote:

Originally Posted by Dan64456 (Post 22302)
And I think it's nonsense that the subject line was tarnished on my OP... I posted this under the GLOCK forum because it is asking about a GLOCK handgun. I don't understand why it was moved and edited by a moderator?

No, not at all. There was a problem with the database that has the forums, subjects and posts and a few posts got messed up. Feel free to repost this on the Glock forum and it should stay put now.

Dan64456 04-23-2008 03:36 PM

My mistake... Thanks for clearing this up for me.


All times are GMT. The time now is 12:42 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.